Multitech MT2834MRK Handbuch

.MultiModemManagerModel CC4800 Card CageHardware Manual

1 - 21.3Special Considerations for CC4800 48 Volt Card CagesThe power supply input screw terminals, located on the bottom right portionof the back of

1 - 3• only connect like circuits. In other words, connect SELV (Secondary ExtraLow Voltage) circuits to SELV circuits and TN (TelecommunicationsNetw

.Chapter 2Installation

2 - 12.1IntroductionThis chapter tells you how to install the power supplies, the rack controllercard, and modem cards into your MultiModemManager Car

2 - 22.2Hardware Installation ProcedureWARNING: When the modem rack is connected to the phone lines, it ispossible for hazardous voltages to be presen

2 - 39. Determine the modem slot(s) to be used and remove front panel slot(s) ifnecessary. Insert the MultiModem cards. Align modem module in cardgu

2 - 4TN 1-16 DB25 Connectors For Phone Line Interface (TNV Circuit)Alarm Connector (SELV)(for future use) DB25S Female RS232 (SELV)(Reserved For Futur

2 - 52.4CablingThe rack back panel provides the connections for rack operation in thesystem. These connectors include:• 16-DB25P male Phone Line Conne

2 - 62.5RJ21 Phone Line Interface OptionThe back panel shown below illustrates the RJ21 version of the Phone LineInterface Board (Model - CC4800-21).

2 - 7RS232 Interface (SELV) ConnectorsCC48-11LPhone Line Interface Board(TNV Circuit)Alarm Connector (SELV)(For Future Use)DB25S Female RS232 (SELV)(R

Owner’s ManualP/N 82024202, Rev. CCC4800, CC4800/11, CC4800/21, and CC4800 48 volt Card CageThis publication may not be reproduced, in whole or in par

.Chapter 3Cable and ConnectorDescriptions

3 - 1Cable and Connector DescriptionsThis chapter illustrates and describes the cables and connectors related tothe MultiModemManager rack. These cab

3 - 23.2CA1432MR Line CableMulti-Tech provides a standard line cable for connecting the MT1432MR orthe MT 2834MR back panel phone line interface to th

3 - 3253.3Dial-Up Line 50-Pin Connector (CC48-21L)These 50-pin RJ21 connectors are used on racks with an RJ21 Dial-upPhone Line Interface Board. We p

3 - 43.4 2-Wire Leased Line or 4-Wire Transmit Pair Connector(CC48-21L)These 50-pin connectors are used on racks with an RJ21 Leased Line PhoneLine I

3 - 550POS.-CHAMP-CONNECTOR3RTIPA1 26 1 RRINGA1 RTIPA9 26 1 RRINGA9RTIPB1 27 2 RRINGB1 RTIPB9 27 2 RRINGB9RTIPC1 28 3 RRINGC1 RTIPC9 28 3 RRINGC9RTIPA

.Chapter 4Service, Warranty& Tech Support

4 - 14.1ServiceIf service is required, equipment may be sent, freight prepaid, to our factory.Return shipping charges will be paid by Multi-Tech Syste

4 - 2MTS WILL NOT BE LIABLE FOR CONSEQUENTIAL DAMAGES ANDUNDER NO CIRCUMSTANCES WILL ITS LIABILITY EXCEED THEPURCHASE PRICE FOR DEFECTIVE PRODUCTS.4.3

.Appendix

safety - 1Important Safety Requirements1. No manual adjustments to the equipment are necessary for connection tomains power within rated voltage and f

appendix - 1Appendix ARelated Products and DocumentationMultiModemManager ProductsMMM-Starter Starter Rack includes either (must specify) a CC4800/11

appendix - 2MR4800 Rack controller module provides the interface betweenthe rack modems and a PC equipped with AN301TP8and MMM software.MMMSW MMM soft

safety - 2Power RequirementsFor CC 4800 48 Volt Card Cage:DC, 42-54V, 7A.CAUTION: For continued protection against risk of fire, replace with sametyp

safety - 3Requisitos de potenciaC.A. 100-240 V, 50/60 Hz, 5-2,5 AmpATTENCION: Para garantizar la protección continua frente al peligro deincendio, su

NOTE: This equipment has been tested and found to comply with the limits fora Class A digital device, pursuant to Part 15 of the FCC rules. These limi

iiiContentsIMPORTANT SAFETY CONSIDERATIONSCHAPTER 1 – INTRODUCTION & DESCRIPTION1.1 Introduction ...

.Chapter 1Introduction & Description

1 - 11.1IntroductionThe CC4800 card cage is the housing for the MultiModemManager,Multi-Tech Systems’ high-density modem management system. The modem