Multitech MTCBA-C-U Spezifikationen Seite 87
- Seite / 197
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Chapter 13 – Specific AT Commands
Multi-Tech Systems, Inc. CDMA AT Commands Reference Guide (PN S000294K) 87
Minute Alert +WMBP
Description: This command is used to set the minute alert while in a voice conversation.
Values: <mode>
0 Disable alert
1 Enable alert
<interval>
1 – 30 Time in minutes
Syntax: Command syntax: AT+WMBP=<mode>,<interval>
Command Possible Responses
AT+WMBP=0
Note: Turn off the alert
OK
AT+WMBP=1,4
Note: Turn on the alert and set 4 minutes apart
OK
AT+WMBP?
Note: Request current setting
+WMBP: 1,4
AT+WMBP=?
Note: Display valid parameter ranges.
+WMBP: (0-1),(1-30)
Configure LED Indicator +CLED
Description: This command is used to configure GPIO 41 and GPIO 54 for general purpose use. The default use of these
two GPIO’s is to drive LED indicators on the Developer Kit board. This command allows a user application to
disable this default behavior. When disabled, the user application has full control over the state of these
GPIO’s. The modem operating software will be prevented from change them for operational status
indications.
The byte value specified with the +CLED command is a bitmap where bit 0 configures LED1/GPIO 41 and
bit 1 configures LED2/GPIO 54. Bit positions 2 through 7 are ignored.
The state of the +CLED specified control bits is not persistent. Both bit positions are always set active (1)
during boot resulting in LED status indicator operation. The +CLED command must be used by the user
application after each boot if GPIO 41 or GPIO 54 are used for other purposes.
Values: <bitmap value>
bit 0 0 = GPIO 41 selected; 1 = LED1 selected.
bit 1 0 = GPIO 54 selected; 1 = LED2 selected.
bit 2 – bit7 Reserved
Syntax: Command syntax: AT+CLED=<bitmap value>
Command Possible Responses
AT+CLED?
Note: Display current settings.
CLED: 3
OK
Note: Both GPIO’s are used for modem operational status
indicators.
AT+CLED=?
Note: Display valid parameter range.
CLED: (0-3)
OK
AT+CLED=1
Note: Set bit 1 to inactive and bit 0 to active.
AT+WIOW=54,0
Note: Set GPIO state.
AT+WIOR=41
Note: Read state of LED1 indicator.
OK
Note: GPIO 54 available, LED1 used for modem status.
OK
Note: Set GPIO 54 to 0.
+WIOR: 1
OK
Note: Read current state of LED1 indicator
AT+CLED=2
Note: Set bit 1 to active and bit 0 to inactive.
AT+WIOW=41,1
Note: Set GPIO state.
AT+WIOW=54,1
Note: Set LED2 state.
OK
Note: LED2 used for modem status, GPIO 41 available.
OK
Note: Set GPIO 41 to 1.
OK
Note: LED2 indicator set to “on”. LED on/off state may
change due to modem status indication.
- CDMA AT Commands 1
- Contents 3
- Chapter 1 – Introduction 9
- Terminology and Acronyms 10
- Chapter 2 – AT Command 13
- Features 13
- Attention AT 14
- Request IMSI +CIMI 15
- Capabilities List +GCAP 15
- Repeat Last Command A/ 15
- Phone Offline +CPOF 16
- Keypad Control +CKPD 17
- Clock Management +CCLK 17
- Ring Melody Playback +CRMP 17
- Ringer Sound Level +CRSL 18
- Subscriber Number +CNUM 18
- View Modem Timers +WTMR 19
- Chapter 4 – Call Control 20
- Hang-Up Command H 21
- Answer a Call A 22
- Remote Disconnection 22
- DTMF Signals +VTD, +VTS 23
- Automatic Answer S0 24
- Incoming Call Bearer +CICB 25
- Microphone Gain +VGT 26
- Volume Gain Control +VGR 26
- Echo Cancellation +ECHO 27
- TTY Mode +WTTY 28
- Chapter 5 – Network Service 29
- Band Preference +WBND 30
- Roam Preference +WRMP 31
- Change NAM Selection +WNAM 32
- Read Current NAM +WCNM 32
- Chapter 6 – SIM Card 35
- Operational Commands 35
- Enter PIN2 +CPIN2 36
- Change Password +CPWD 38
- Card Identification +CCID 38
- Chapter 7 – Short Messages 39
- Delete Message +CMGD 47
- Message Overwriting +WMGO 49
- Change SMS Status +WUSS 49
- Chapter 8 – Supplementary 51
- Services Commands 51
- Chapter 9 – Data Commands 55
- Cellular Result Codes +CRC 56
- Chapter 10 – V.24-V.25 58
- Set DCD Signal &C 59
- Set DTR Signal &D 60
- Set DSR Signal &S 60
- Back to Online Mode O 60
- Result Code Suppression Q 60
- DCE Response Format V 61
- Audio Loopback &T 61
- Echo E 61
- Save Configuration &W 62
- Chapter 11 – Phone Book 63
- Phonebook Read +CPBR 66
- Phonebook Search +CPBP 66
- Chapter 12 – Position 68
- Determination (GPS) 68
- IP Server Address +WMPC 73
- Chapter 13 - Specific AT 74
- Read GPIO Value +WIOR 78
- Write GPIO Value +WIOW 78
- Play Tone +WTONE 78
- Play DTMF Tone +WDTMF 79
- Hardware Version +WHWV 79
- Select Voice Gain +WSVG 80
- Status Request +WSTR 80
- Ring Indicator Mode +WRIM 81
- 32kHz Sleep Mode +W32K 81
- Software Version +WSSW 82
- CPHS Command +CPHS 83
- Reset +WRST 84
- Set Standard Tone +WSST 85
- Security PIN +WPIN 86
- Minute Alert +WMBP 87
- Chapter 14 - SIM ToolKit for 89
- RUIM Software Version 89
- Example: 91
- Chapter 15 – Provisioning AT 99
- Set IMSI +WIMI 100
- SID and NID +WSID 101
- Slot Cycle Index +WSCI 101
- Packet Dial String +WPDS 102
- Commit Changes +WCMT 104
- Read SID/NID Entries +WSNR 104
- Download PRL +DPRL 105
- Service Programming Example 106
- Chapter 16 – Extended AT 107
- Commands in IS707.3 107
- Select Pulse Dialing P 108
- Basic S-Registers S 108
- Error Control Report +ER 109
- Modulation Selection +MS 113
- V.18 Selection +MV18S 114
- Cellular Extension +CXT 115
- Configuration String +CFG 115
- Query Service +CAD 115
- Battery Charge +CBC 117
- Serving System +CSS 118
- Hang-up Voice +CHV 119
- Chapter 17 – Qualcomm 121
- Defined AT Commands for 121
- CDMA Operation 121
- Set DM Baud Rate $QCDMR 125
- SCRM’ing Selection $QCSCRM 126
- R-SCH IP Selection $QCMIP 127
- MIP Selection $QCMIPP 128
- Chapter 18 – TCP/IP App AT 133
- Commands 133
- Open Socket +WOSK 134
- Close Socket +WCSK 135
- Transmit Socket Data +WSTX 135
- Read Receive Data +WSRX 136
- Force Dormant Mode +WFDM 138
- IP Address Lookup +WDNS 139
- Display IP Address +WIPC 139
- PPP Session Status +WPPP 139
- Socket State Change +WSKS 140
- Received Socket Data +WSRX 141
- Socket Data Error +WSRE 141
- Chapter 19 – Reference 143
- Information 143
- Specific Error Result Codes 144
- Final Result Codes 145
- Intermediate Result Codes 145
- Parameters Storage 147
- TCP App Socket Status Events 150
- TCP App Socket Error Codes 150
- TCP App DNS Server Codes 150
- TCP App PPP Network Codes 150
- Phonebook UCS2 Unicode 152
- MuxLite Example 154
- Chapter 20 – Unsolicited AT 155
- Result Codes 155
- Key Press or Release +CKEV 156
- Mode Preference +COPS 158
- Incoming Call +CRING 158
- RxLev Indication +CSQ 159
- Incoming Call +RING 159
- Call Answered +WANS 159
- Call Connected +WCNT 160
- Call Ended +WEND 160
- Flash Indication +WFSH 161
- General Indicator +WIND 161
- Call Originated +WORG 162
- Roaming Indication +WROM 162
- Emergency Mode +WSOS 163
- Current NAM Change +WNAM 163
- Voice Mail Indicator +WVMI 164
- Power Save +WSPS 164
- Download PRL Status +DPRL 167
- Chapter 21 – AT Command 168
- Examples 168
- Incoming Voice Call 169
- Call Waiting 169
- Originate Data Call 169
- Originate Data Call Failure 169
- Short Message Examples 170
- GpsOne Examples 171
- AT Commands 175
- Read Message +CMGR 177
- List Message +CMGL 178
- Send Message +CMGS 179
- Facility Lock +CLCK 185
- Signal Quality +CSQ 185
- Boot URL +WBURL 187
- Trusted Domain +WTDMN 187
- Proxy Address +WDPXY 187
- IOTA Error +WOAE 188
- Please Retry +WOAR 188
- Display PRI Checksum +WSUM 189
Verwandte Produkte und Handbücher für Vernetzung Multitech MTCBA-C-U
Vernetzung Multitech FaxFinder FF840 Spezifikationen
(116 Seiten)
(116 Seiten)
Vernetzung Multitech CF220 Betriebsanweisung
(12 Seiten)
(12 Seiten)
Vernetzung Multitech MTCBA-G-UF1 Spezifikationen
(40 Seiten)
(40 Seiten)
(58 Seiten)
Vernetzung Multitech FR2201 Betriebsanweisung
(28 Seiten)
(28 Seiten)
Vernetzung Multitech RF802EW Betriebsanweisung
(28 Seiten)
(28 Seiten)
Vernetzung Multitech MA220 Betriebsanweisung
(80 Seiten)
(80 Seiten)
Vernetzung Multitech MA100-1M Betriebsanweisung
(71 Seiten)
(71 Seiten)
Vernetzung Multitech FF200 Betriebsanweisung
(169 Seiten)
(169 Seiten)
Campbell CVF4 podręczniki
Instrukcje obsługi i podręczniki użytkownika dla Nie Campbell CVF4.
Dostarczamy 2 pdf podręczników Campbell CVF4 do pobrania za darmo według typów dokumentów: Instrukcja Obsługi
Campbell CVF4 Instrukcja Obsługi (42 strony)
Marka: Campbell | Kategoria: No info | Rozmiar: 1.39 MB |
Spis treści
Figures
5
4.2 Mounting
10
5. Overview
13
7.2 Wiring
19
Ventilator
34
A.3.1 CVF3
36
Ø 7 mm (2x)
38
A.4 Wiring
40
A.5.2 CVF4
41
Campbell CVF4 Instrukcja Obsługi (27 strony)
Marka: Campbell | Kategoria: No info | Rozmiar: 0.98 MB |
Spis treści
Ø 7 mm (2x)
13
HEAD OFFICE
27
Więcej produktów i instrukcji dla Nie Campbell
| Modele | Rodzaj dokumentu |
|---|---|
| SC-USB |
Podręcznik Użytkownika
Campbell SC-USB User guide,
26 strony
|
| SC-USB |
Instrukcja Obsługi
Campbell SC-USB Product manual,
36 strony
|
| KH20 |
Instrukcja Obsługi
Campbell KH20 Instruction manual [en] ,
48 strony
|
| SDM-CD16D |
Podręcznik Użytkownika
Campbell SDM-CD16D User guide,
17 strony
|
| CS505 |
Instrukcja Użytkownika
Model CS205 10-Hour Fuel Temperature Stick [en] ,
10 strony
|
| 25458 |
Instrukcja Użytkownika
25458 DIN-Rail Terminal Kit [en] [it] ,
10 strony
|
| CS210 |
Instrukcja Użytkownika
CS210 Manual - Campbell Scientific,
14 strony
|
| TX312 |
Instrukcja Użytkownika
Snotel Goes Manual R2b,
10 strony
|
| SDM-CD16D |
Dokumentacja
Campbell SDM-CD16D Specifications,
20 strony
|
| TDR |
Instrukcja Użytkownika
Comparison of laboratory TDR soil water measurements,
16 strony
|
| CompactFlash CFM100 |
Instrukcja Obsługi
Campbell CompactFlash CFM100 Instruction manual,
32 strony
|
| SC932C 9-Pin |
Podręcznik Użytkownika
Campbell SC932C 9-Pin User guide,
16 strony
|
| CompactFlash CFM100 |
Instrukcja Obsługi
Campbell CompactFlash CFM100 Product manual [en] ,
28 strony
|
| CS525 |
Instrukcja Użytkownika
CS525 - Campbell Scientific,
2 strony
|
| TX320 |
Instrukcja Użytkownika
La Désirade et Deshaies : choix technologiques et - Refmar,
14 strony
|
| RTMS SYSTEMS |
Instrukcja Obsługi
Campbell RTMS SYSTEMS Instruction manual,
58 strony
|
| RWIS STATIONS |
Instrukcja Użytkownika
Flood, Road, and Weather Data in Colorado,
2 strony
|
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.030 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern