Multitech SF100-G-EU Spezifikationen PDF herunterladen (Seite 16)

MultiModem® iSMS Administrator’s Guide 16

Chapter 2 – Setting up and using the

iSMS

Setting Up Your MultiModem iSMS

New MultiModem iSMS units are preconfigured with an IP address of 192.168.2.1 and a 24 bit subnet mask

(255.255.255.000).

Before connecting your new MultiModem iSMS to your network and powering it up, identify the existing IP network

numbering scheme of the target network. If the target network already implements a 192.168.2.xxx class C network, the

unit's host IP address of 192.168.2.1 may conflict with an existing computer or device on the network. Additionally,

advanced network configurations may block IP packets not of the current scheme. For example, if the current network

configuration is 10.1.x.x/16, any IP packets not of this subnet are blocked.

If either is the case, temporarily isolate a workstation and the new MultiModem iSMS from the target network. Connect

the Ethernet interface of the workstation directly to the Ethernet interface of the MultiModem iSMS. After configuring

the MultiModem iSMS with appropriate IP network parameters (IP address, subnet mask, default gateway and DNS), you

can connect the MultiModem iSMS to the target network.

Note: Be sure to perform a "Save to Flash" before powering off the unit, if you are physically moving the unit to a new

location.

The MultiModem iSMS LAN connection is a full duplex, auto negotiating 10/100 MHz, auto polarity sensing Ethernet

interface. You can use a traditional straight through RJ-45 Ethernet cable or a cross-over RJ-45 Ethernet cable when

connecting to an Ethernet port on a hub or switch or when connecting directly to the Ethernet interface of a workstation.

The LAN connection of the MultiModem iSMS does not

support POE (Power over Ethernet) or 1GHz. These features may

need to be disabled on the equipment/port that the MultiModem iSMS is connected to.

You must cable and then configure your device:

● Basic cabling and TCP/IP directions are included in this chapter.

● Chapter 3 describes basic configurations.

● Chapter 4 describes advanced configurations.

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 125 126

Keine Kommentare

Modele	Rodzaj dokumentu
SC-USB	Podręcznik Użytkownika Campbell SC-USB User guide, 26 strony
SC-USB	Instrukcja Obsługi Campbell SC-USB Product manual, 36 strony
KH20	Instrukcja Obsługi Campbell KH20 Instruction manual [en] , 48 strony
SDM-CD16D	Podręcznik Użytkownika Campbell SDM-CD16D User guide, 17 strony
CS505	Instrukcja Użytkownika Model CS205 10-Hour Fuel Temperature Stick [en] , 10 strony
25458	Instrukcja Użytkownika 25458 DIN-Rail Terminal Kit [en] [it] , 10 strony
CS210	Instrukcja Użytkownika CS210 Manual - Campbell Scientific, 14 strony
TX312	Instrukcja Użytkownika Snotel Goes Manual R2b, 10 strony
SDM-CD16D	Dokumentacja Campbell SDM-CD16D Specifications, 20 strony
TDR	Instrukcja Użytkownika Comparison of laboratory TDR soil water measurements, 16 strony
CompactFlash CFM100	Instrukcja Obsługi Campbell CompactFlash CFM100 Instruction manual, 32 strony
SC932C 9-Pin	Podręcznik Użytkownika Campbell SC932C 9-Pin User guide, 16 strony
CompactFlash CFM100	Instrukcja Obsługi Campbell CompactFlash CFM100 Product manual [en] , 28 strony
CS525	Instrukcja Użytkownika CS525 - Campbell Scientific, 2 strony
TX320	Instrukcja Użytkownika La Désirade et Deshaies : choix technologiques et - Refmar, 14 strony
RTMS SYSTEMS	Instrukcja Obsługi Campbell RTMS SYSTEMS Instruction manual, 58 strony
RWIS STATIONS	Instrukcja Użytkownika Flood, Road, and Weather Data in Colorado, 2 strony

Multitech SF100-G-EU Spezifikationen Seite 16